Fire Stop Supplies

Passive Fire Protection

Ablative Coated Batt

£24.68 – £28.58

PLEASE NOTE: This product is available for collection only. Alternatively we can deliver within a 15 mile radius from our office, PR4 4JX. Please contact us on 01772 379449 or info@firestopsuppliesltd.co.uk for more information.

The ROCKWOOL 50mm Ablative Coated Batt is a mineral wool insulation product, pre – coated on both sides with a high performance ablative coating. It has been comprehensively tested as part of the ROCKWOOL FIREPRO® range of fire protection products and can be installed across a variety of services and substrates including solid walls and floors, flexible walls, multi-service penetrations, the head of wall, blank seals and face fixed applications as well as large framed service voids. The Ablative Coated Batt is tested to provide up to 4 hours fire resistance whilst also providing an excellent acoustic performance and importantly, maintaining air tightness and reducing unwanted heat losses. Ablative Coated Batts are not intended for use as load-bearing seals. Where a load bearing seal is required, ROCKWOOL Firestop Compound should be considered.

facebookFacebook
TwitterTweet
FollowFollow us
SKU: N/A Categories: ,

PLEASE NOTE: This product is available for collection only. Alternatively we can deliver within a 15 mile radius from our office, PR4 4JX. Please contact us on 01772 379449 or info@firestopsuppliesltd.co.uk for more information.

  • Ease of installation - the ROCKWOOL Ablative Coated batt can be easily cut to the size and shape required to fit the aperture and penetrations.  Cuts to the batt should be kept to a minimum.
  • Application - ROCKWOOL Acoustic Intumescent Sealant to be applied to all cut edges of the batt ensuring an even cover is achieved over the entire thickness of the batt. Some applications may require the use of the FIREPRO Glue to cut edges.
  • Excellent fire resistance from a single thickness batt - tests have proved the capability of a single 50mm Batt to provide up to 2 hours fire resistance integrity and insulation. Where 4 hours integrity and insulation is required, the use of the 60mm Ablative Coated Batt is recommended.
  • Durable – a reliable and long lasting insulation solution.
  • Tested for airtightness – also providing the crucial benefits of a proven acoustic seal and preventing the passage of smoke.
  • Environmental – as with all ROCKWOOL products, the Ablative Coated Batt is made from a renewable and plentiful naturally occurring resource. ROCKWOOL insulation saves fuel costs and energy in use and relies on trapped air for its thermal properties.

Accreditations:

  • BS EN 1366-3: 2009 and the dedicated fire resistance standard for linear joint seals
  • BS EN 1366-4:2006
  • Ablative Coated Batt has been classified in accordance with BS EN 13501-2
  • Third party accreditation through Certifire
  • CE Marked to EAD 350454-00-1104 - ETA 20/1128
Installation
1. Make sure that the area within the aperture is clean of any debris and remove any dust from the edges.
2. Cut ROCKWOOL Ablative Coated Batt to the size and shape required to fit the aperture ensuring that batt will make a tight fit with all edges of the aperture.
3. Cut rectangular holes form the coated batt to accommodate cable trays or ladders containing cables.
4. Cut the Coated Batt across its width at the mid-point of each rectangular hole to enable the Batt to be fitted into the aperture.
5. Apply ROCKWOOL Acoustic Intumescent Sealant to all edges of the Batt ensuring that an even cover is achieved over the entire thickness of the Batt. This should include the outer edges of the Batt and the edges of the cuts made across the Batt to allow fitting into the aperture. There is no requirement to apply sealant to the edges of the holes cut to accommodate cable trays or ladders.
6. Insert the Batt into the aperture.
7. Apply a bead of ROCKWOOL Acoustic Intumescent Sealant approximately 15mm wide around the perimeter of the Batt ensuring that all gaps between the Batt and surrounding edges are fully filled.
8. Apply a bead of ROCKWOOL Acoustic Intumescent Sealant approximately 15mm wide where cables pass through the Batt. Ensure that the sealant fully enclosed each cable within the tray or ladder and that all gaps are fully filled.
 9. Repeat step 7 and 8 on the other side of the Batt.

Additional information

Size

1200mm x 600mm x 50mm, 1200mm  x 600mm x 60mm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Related products

Sale